Menu
Take this information as a guide for how we would normally hang one of our hanging chairs or daybeds.
This may not be suitable in some circumstances and your builder may suggest another way.
Consider Your Roof Strength
For a concrete roof structure, the concrete roof should be a minimum 120mm thickness. If in doubt consult with a licensed builder or carpenter. We suggest allowing for a minimum of 400mm swing room at the rear of the swing to any wall structures.
Mark Out Hanging Points
Allow for approximately 40mm greater width, than the actual width of daybed or swing. For example if your hanging chair is 1500mm in length, then allow of 1540mm width between hanging points.
Please refer to our Product Spec Sheet for full hanging measurements.
As some of the daybeds are 4-point hanging, you will need to mark out the 4 points on the roof as to where it will hang.
A couple of key measurements:
Off a back wall- min 500mm
From a side wall- min 300mm
Hanging height- up to you what you prefer, however, we’d generally say about 500mm from the ground is a comfortable height to get on and off from.
Install Eye Bolts Into To Roof
Use M12 Eye bolts
Drill 2x 12mm hole into the concrete roof approx 80mm in depth
Clean out drill holes to ensure no dust remains in holes
Add Chemset into the drilled hole
Insert the M12 eye bolts into the chemset drilled holes
** Chemset will set very quickly!
(Can be purchased from any hardware or bunnings store)
Wait 24hrs before moving on to the next step
Clip On The Carabiner (2-point hanging)
Now that you have installed the eye nuts into the roof, clip one carabiner onto each of the eye nuts.
Let the ropes hang down and pass through eye bolts that are on the base of the chair.
Prop the swing on something that is approximately 500mm in height (ie a small table / 2 chairs etc), so that you can get the right height for your swing.
NOTE: When you first sit on the swing / day bed the ropes will stretch to a final position, as such, allow for the position to be approximately 50mm higher than anticipated.
Or
Use Split Links (4-point hanging)
Use the split link through one link of the chain and clip it onto the eyebolt. Thread the chain through the spliced part of the rope.
Place the other end of the link chain on the other end of the split link.
These links are used to adjust the height and tilt of your hanging daybed.
Get The Right Tilt
For a Hanging Chair- Allow the back of the swing to be slightly lower than the front of your swing.
Whatever you have the swing resting on, allow the front edge of it to sit slightly higher than the back. This slight tilt will make getting on and off the swing easier and allow for a better back resting position.
For a hanging Daybed- We’d recommend having the bed level from side to side and back-to-front.
Once you have the right height then tighten up the bolts on the rope clamps at the base of the swing.
Wrap/ knot the remainder of the rope around the clamp and remove the temporary support. The rope at the base of the hanging chair is purely for aesthetic purposes. The weight is supported by the clamps.
The knots at the base of the 4-point hanging daybeds are more substantial and can hold the weight of the swing.
See here for an example of how to do a locking knot.
NOTE: When you first sit on the swing/day bed the ropes will stretch to a final position.
This is the best bit!
Once all the hard work is done, sit back, relax, and grab a drink to celebrate.
Fill in the form below if you’d like us to review installation options for you.
We pride ourselves on craftsmanship blended with affordability to create unique yet timeless hanging chairs that will lighten up any outdoor space in your home.
We are an Aussie family business that loves the outdoors and loves creating products to enhance the connectivity within the landscape. Swings are a beautiful way to appreciate the quiet moments but also connect with others.
We invite you to create your own barefoot luxury style with our swing chairs.
We use wherever possible local Aussie suppliers, businesses and eco-friendly products.
Copyright © 2022 Cartia Collective. All Rights Reserved